ASTM A888-18a
Original price was: $94.00.$47.00Current price is: $47.00.
Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
ASTM International , 11/15/2018
Pages: 59
1.1This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
1.2The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.
1.3This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.2
1.3.1Lengths:
|
Figures |
|
|
EDP/ASA Identification Numbers for Hubless Pipe |
Fig. 1 |
|
10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 11/2, 2, 3, 4, 5, 6, 8, 10, 12, and 15 in. |
Fig. 1, Fig. 2 |
|
Method of Specifying Fittings |
Fig. 3 |
1.3.2Fittings:
|
Quarter Bend |
Fig. 5 |
|
Quarter Bend, Reducing |
Fig. 6 |
|
Quarter Bend, with Side Opening |
Fig. 7 |
|
Quarter Bend, with Heel Opening |
Fig. 8 |
|
Quarter Bend, Tapped |
Fig. 9 |
|
Quarter Bend, Double |
Fig. 10 |
|
Quarter Bend, Long |
Fig. 11 |
|
Short Sweep |
Fig. 12 |
|
Long Sweep |
Fig. 13 |
|
Long Sweep, Reducing |
Fig. 14 |
|
Fifth Bend |
Fig. 15 |
|
Sixth Bend |
Fig. 16 |
|
Eighth Bend |
Fig. 17 |
|
Eighth Bend, Long |
Fig. 18 |
|
Sixteenth Bend |
Fig. 19 |
|
Sanitary Tee |
Fig. 20 |
|
Sanitary Tee with Side Opening |
Fig. 21 |
|
Sanitary Tee with 2 in. Side Opening R or L/R and L |
Fig. 22 |
|
Sanitary Tee, New Orleans Special with Side Opening |
Fig. 23 |
|
Sanitary Tee with 45° Side Openings and New Orleans |
Fig. 24 |
|
Sanitary Special Tee Tapped |
Fig. 25 |
|
Sanitary Tapped Tee, Horizontal Twin |
Fig. 26 |
|
Sanitary Tapped Tee, Double Vertical |
Fig. 27 |
|
Y Branch |
Fig. 28 |
|
Y Branch, Double |
Fig. 29 |
|
Y Branch, Upright |
Fig. 30 |
|
Upright Y Wide Center Florida Special |
Fig. 31 |
|
Y Branch, Combination 1/8Bend |
Fig. 32 |
|
Y Branch, Combination 1/8Bend Double |
Fig. 33 |
|
Sanitary Cross |
Fig. 34 |
|
Sanitary Cross with Side Opening |
Fig. 35 |
|
Sanitary Cross, New Orleans, with Side Openings |
Fig. 36 |
|
Sanitary Cross, New Orleans, with 45° Special and Regular Side Openings |
Fig. 37 |
|
Sanitary Cross, Tapped |
Fig. 38 |
|
Test Tee |
Fig. 39 |
|
Tapped Extension Piece |
Fig. 40 |
|
Increaser-Reducer |
Fig. 41 |
|
Increaser-Reducer, Short |
Fig. 42 |
|
Tapped Adapter |
Fig. 43 |
|
Blind Plug |
Fig. 44 |
|
Iron Body Cleanout, Tapped |
Fig. 45 |
|
P Trap |
Fig. 46 |
|
P Trap, Long |
Fig. 47 |
|
P Trap, Deep Seal |
Fig. 48 |
|
P Trap, with Primer |
Fig. 49 |
|
P Trap, with Tapped Inlet |
Fig. 50 |
|
Tapped Inlet, Double |
Fig. 51 |
|
Modified Combination Wye and 1/8 Bend, Double |
Fig. 52 |
|
Modified Combination Wye and 1/8 Bend, Double, Extended |
Fig. 53 |
|
Two-Way Cleanout |
Fig. 54 |
|
Twin Cleanout |
Fig. 55 |
|
Closet Bend, Regular and Reducing |
Fig. 56 |
|
Closet Flange Riser |
Fig. 57 |
|
Tapping Bosses |
Fig. 58 |
|
Double Sweep Sanitary Tee (Extended) |
Fig. 59 |
|
Running Trap with Double Vents |
Fig. 60 |
|
P Trap with Tapped or Hubless Side Inlet |
Fig. 61 |
|
Vented Tub Wye Extended, Double |
Fig. 62 |
|
Vented Tub Wye Extended Offset, Left or Right |
Fig. 63 |
|
Vented Tub Wye |
Fig. 64 |
|
Double Two-Way Cleanout |
Fig. 65 |
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301.
Note 1:The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Related products
