ASTM A615/A615M-14
Original price was: $60.00.$30.00Current price is: $30.00.
Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
ASTM International , 04/01/2014
Pages: 7
1.1This specification covers deformed and plain carbon-steel bars in cut lengths and coils for concrete reinforcement. Steel bars containing alloy additions, such as with the Association for Iron and Steel Technology and the Society of Automotive Engineers series of alloy steels, are permitted if the resulting product meets all the other requirements of this specification. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1.
|
Bar Designation No. |
Nominal Weight, lb/ft [Nominal Mass, kg/m] |
Nominal DimensionsA |
Deformation Requirements, in. [mm] |
||||
|
Diameter, in. [mm] |
Cross-Sectional Area, in. 2 [mm²] |
Perimeter, in. [mm] |
Maximum Average Spacing |
Minimum Average Height |
Maximum Gap (Chord of 12.5 % of Nominal Perimeter) |
||
|
3 [10] |
0.376 [0.560] |
0.375 [9.5] |
0.11 [71] |
1.178 [29.9] |
0.262 [6.7] |
0.015 [0.38] |
0.143 [3.6] |
|
4 [13] |
0.668 [0.994] |
0.500 [12.7] |
0.20 [129] |
1.571 [39.9] |
0.350 [8.9] |
0.020 [0.51] |
0.191 [4.9] |
|
5 [16] |
1.043 [1.552] |
0.625 [15.9] |
0.31 [199] |
1.963 [49.9] |
0.437 [11.1] |
0.028 [0.71] |
0.239 [6.1] |
|
6 [19] |
1.502 [2.235] |
0.750 [19.1] |
0.44 [284] |
2.356 [59.8] |
0.525 [13.3] |
0.038 [0.97] |
0.286 [7.3] |
|
7 [22] |
2.044 [3.042] |
0.875 [22.2] |
0.60 [387] |
2.749 [69.8] |
0.612 [15.5] |
0.044 [1.12] |
0.334 [8.5] |
|
8 [25] |
2.670 [3.973] |
1.000 [25.4] |
0.79 [510] |
3.142 [79.8] |
0.700 [17.8] |
0.050 [1.27] |
0.383 [9.7] |
|
9 [29] |
3.400 [5.060] |
1.128 [28.7] |
1.00 [645] |
3.544 [90.0] |
0.790 [20.1] |
0.056 [1.42] |
0.431 [10.9] |
|
10 [32] |
4.303 [6.404] |
1.270 [32.3] |
1.27 [819] |
3.990 [101.3] |
0.889 [22.6] |
0.064 [1.63] |
0.487 [12.4] |
|
11 [36] |
5.313 [7.907] |
1.410 [35.8] |
1.56 [1006] |
4.430 [112.5] |
0.987 [25.1] |
0.071 [1.80] |
0.540 [13.7] |
|
14 [43] |
7.65 [11.38] |
1.693 [43.0] |
2.25 [1452] |
5.32 [135.1] |
1.185 [30.1] |
0.085 [2.16] |
0.648 [16.5] |
|
18 [57] |
13.60 [20.24] |
2.257 [57.3] |
4.00 [2581] |
7.09 [180.1] |
1.58 [40.1] |
0.102 [2.59] |
0.864 [21.9] |
1.2Bars are of four minimum yield strength levels: namely, 40 000 psi [280 MPa], 60 000 psi [420 MPa], 75 000 psi [520 MPa], and 80 000 psi [550 MPa], designated as Grade 40 [280], Grade 60 [420], Grade 75 [520], and Grade 80 [550], respectively.
1.3Plain bars, in sizes up to and including 21/2in. [63.5 mm] in diameter in coils or cut lengths, when ordered shall be furnished under this specification in Grade 40 [280], Grade 60 [420], Grade 75 [520], and Grade 80 [550]. For ductility properties (elongation and bending), test provisions of the nearest smaller nominal diameter deformed bar size shall apply. Requirements providing for deformations and marking shall not be applicable.
1.4Requirements for alternate bar sizes are presented in Annex A1. The requirements in Annex A1 only apply when specified by the purchaser (see 4.2.4).
1.5The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification.
1.6This specification is applicable for orders in either inch-pound units (as Specification A615) or in SI units (as Specification A615M).
1.7The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification.
1.8This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Related products
