ASTM F606/F606M-24
Original price was: $76.00.$38.00Current price is: $38.00.
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM International , 11/01/2024
Pages: 19
1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets.
1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply.
1.3 These test methods describe mechanical tests for determining the following properties:
Section For Externally Threaded Fasteners: 3 Product Hardness 3.1 Proof Load 3.2.1 Method 1, Length Measurement 3.2.3 Method 2, Yield Strength 3.2.4 Method 3, Uniform Hardness 3.2.5 Axial Tension Testing of Full-Size Product 3.4 Wedge Tension Testing of Full-Size Product 3.5 Tension Testing of Machined Test Specimens 3.6 Total Extension at Fracture Test
Single Sheer Test 3.7
3.8 For Internally Threaded Fasteners: 4 Product Hardness 4.1 Proof Load Test 4.2 Cone Proof Load Test 4.3 For Washers and Direct Tension Indicators: 5 Product Hardness-General Requirements 5.1 Through Hardened Washers 5.2 Carburized Washers 5.3 Stainless Steel and Nonferrous Washers 5.4 Direct Tension Indicators 5.5 Compression Load 5.6 For Rivets: 6 Product Hardness 6.1 Test for Embrittlement of Metallic-Coated Externally Threaded Fasteners 7 Test Method for Determining Decarburization and Carburization 8
Single Sheer Test 3.7
3.8 For Internally Threaded Fasteners: 4 Product Hardness 4.1 Proof Load Test 4.2 Cone Proof Load Test 4.3 For Washers and Direct Tension Indicators: 5 Product Hardness-General Requirements 5.1 Through Hardened Washers 5.2 Carburized Washers 5.3 Stainless Steel and Nonferrous Washers 5.4 Direct Tension Indicators 5.5 Compression Load 5.6 For Rivets: 6 Product Hardness 6.1 Test for Embrittlement of Metallic-Coated Externally Threaded Fasteners 7 Test Method for Determining Decarburization and Carburization 8
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
Note 1: The values are stated in inch-pound for inch fasteners and SI metric units for metric fasteners.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Related products
Original price was: $86.00.$43.00Current price is: $43.00.
Original price was: $60.00.$30.00Current price is: $30.00.
Original price was: $52.00.$26.00Current price is: $26.00.
Original price was: $60.00.$30.00Current price is: $30.00.
Original price was: $58.00.$29.00Current price is: $29.00.
Original price was: $50.00.$25.00Current price is: $25.00.
Original price was: $60.00.$30.00Current price is: $30.00.
Original price was: $52.00.$26.00Current price is: $26.00.